Home

http://www.setup.ampedwireless.com is a local web address used to access and to configure amped wireless networking devices like routers, extenders, modems, and USB adapters. It allows you to log in to the web-based interface for amped wireless.

How to setup Amped Wireless through setup.ampedwireless.com or 192.168.1.240

STEP 1 : Turn off your existing wi-fi router from your modem as well as from the computer ,if you are not using any existing router skip this step.

STEP 2 : Connect all antennas to your amped wireless router ,& connect a Ethernet cable from modem to your amped wireless router WAN slot.

STEP 3 : Turn off your modem, unplug power cable from modem for 10 seconds , turn off amped wireless router also.

STEP 4 : Turn on modem first ,wait for 1 minute , then turn on Amped Wireless router.

STEP 5 : Connect a Ethernet cable from amped wireless router to your computer or laptop.

STEP 6 : Launch a web browser ,type http://setup.ampedwireless.com in address bar of your browser , a login screen will appear ,in Case of first time set up ,setup configuration screen will appear.

 

STEP 7 : Amped Wireless router will detect the type of internet connection you are using as per your internet service provider , i.e static, dynamic, pppoe. 

STEP1 : Turn off your existing wifi router from your modem as well as from the computer ,if you are not using any existing router skip this step

SERVICES

Personalizing Wi-fi Settings

After initial internet setup, you can personalize the default network name SSID & network key passphrase settings, network key passphrase Should be a minimum of 8 characters, security type recommended is WPA / wpa2 personal. After personalizing wi-fi settings, you can create a new login username and password, the default login username & password can be used subsequently in the future.

Amped Wireless Firmware Update

Amped wireless router firmware can be easily updated by logging into Amped Wireless router page using a web-based address, Under Firmware settings, you can easily update your router firmware to the latest, or alternatively, you can manually download the firmware version from the amped wireless elite support website.  

Amped Wireless Features

1. MU-MIMO WIFI TECHNOLOGY

2. BEAMFORMING TECHNOLOGY

3. BANDWIDTH OPTIMIZATION

4. SECURITY SOLUTIONS WITH SPI FIREWALL

5. ULTIMATE GAMING WITH ZERO LAG

6.  FILE SHARING

7. MULTI USER MU-MIMO

8. PARENTAL CONTROL FEATURES

9. PORT FORWARDING /PORT TRIGERRING

10. IP FILTERING FEATURES

 

FIX : When you try to access setup.ampedwireless.com , you might receive an error message page cannot be displayed or bad gateway error , in such cases make sure Ethernet cable coming from amped wireless router is connected properly to your computer, do not connect your computer wirelessly with amped wireless router,if your computer is connected to some other wireless router disable wifi adapter of your computer & then try make sure your firewall programs are disabled like avg internet security software ,Norton ,Avast, or Kaspersky security software. 

Amped Wireless Setup

Security Features in Amped Wireless Router

Amped Wireless Routers make sure your Network remains Secured with Security Features. Amped Wireless Router has Number of Security Features. So that, Amped Router users can control access to their wireless network through Specific user authorizations, wireless coverage control or on/off schedules. We are providing an overview of the Amped Wireless Router security features 

Amped SR10000 Setup

AMPED RANGE EXTENDERS 

•  ATHENA EX AC 2600 EXTENDER
• EX HELIOS AC 2200 DIRECTLINK
• HIGH POWER DUAL BAND AC 1750
• HIGH POWER 700MW
• AC 1750 RANGE EXTENDER
• ARTEMIS RANGE EXTENDER AC 3150
• TITAN EX AC 1900 EXTENDER
• HIGH POWER AC 750 TOUCH SCREEN
• DEFAULT LOGIN : https://setup-amped-wireless.com or setup-amped-wireless.com
• IP ADDRESS : 192.168.1.1

How can I set up my Amped Wireless Range Extender

If your Wi-Fi device supports WPS one-touch setup, you can do this by following these steps:

• Press and hold the WPS button located on the back panel your Amped wireless router for approximately 2-3 seconds.
• The power LED on the amped wireless router will start to blink.
• Push the WPS button on your wireless adapter. Or, use the software provided to enable WPS.
• WPS will then automatically configure and establish connection settings for your wireless adapter in order to connect to your Amped wireless router.

If Setup.ampedwireless.com is not responding?

Sometimes when you are trying to access setup.ampedwireless.com, you may see an error message that the page cannot be displayed or a bad gateway error.

First, make sure the Ethernet cable from your wireless router is properly connected to your computer.

Do not connect your computer wirelessly with an amplified wireless router. If your computer is connected to another wireless router, disable Wi-Fi adapter and make sure that firewall programs are disabled.

How do you reset your Amped wireless router

These methods can reset the Amped wireless router to factory default settings:

Use the Reset button

The web interface to the router

The steps below make it easy to reset via the reset button.

• The reset/restore key is located at the back.
• Use a straightened paperclip or pin to press the reset button. After about ten seconds, release the button.
• Wait for a few minutes until the LED light flashes. This is an indicator that your Amped wireless router’s factory default settings have been restored.

Log in to the web-based interface for the amped wireless router to reset the router

• Go to www.setup.ampedwireless.com through a web browser.
• To access the admin page, enter your default login credentials.
• Click on the factory reset tab in the settings page to restore factory settings.

What if you are unable to open the web menu of the amped wireless router after you enter the www.setup.ampedwireless.com?

• Secure Ethernet cables are used to ensure that your computer is connected properly to the wireless router.
• You should ensure that you’re using the most recent and compatible browser. If you still have issues, you can try a different browser (recommended Google Chrome), or close the browser and reopen it.
• Try using the default IP address 192.168.3.1 to access login page instead of web address setup.ampedwireless.com.
• Power cycle your Amped wireless router.
• You can reset the wireless router that is amped at the end, if the rest of your settings are changed to factory defaults by holding down the reset button for a few seconds, and then releasing the button.

What happens if the Smart Setup Wizard does not automatically configure the internet connection?

• Reboot your router by unplugging it and then plugging it in.
• You can also reset your router to its default settings.
• You will need to enter login details for your internet provider if you are using DSL.
• Your internet connection might require static IP. To obtain these settings, you will need to contact your ISP.
• You may need to clone the MAC address of your computer in order for it to work with Internet connections. For this, go to More Settings > IP settings > Internet Network (WAN). Select Automatic/Dynamic from the drop-down menu and Clone the MAC address of your PC under the DNS settings.

Setup of an amped wireless range extender

You will need to locate a suitable spot that is approximately halfway between your Wi Fi router and the Wi Fi dead zone. You should ensure that the range extender is receiving strong signal strength from your Wi Fi router wherever it is placed.

• Attach the antennas to the back of your range extender
• Securely connect your computer to the range extender
• Open any specific web browser and visit www.setup.ampedwireless.com to access the web menu
• Alternately, you can log in with a default IP 192.168.1.240 to access the web menu for the amped wireless extender.
• The Web menu dashboard screen displays the current status of your range extender. After that, click on Scan to locate any networks available to extend.
• Choose the wireless networks that you wish to repeat or expand. To move on, click on Next.
• Enter a password to your Wireless network. To continue, click Next
• By entering a new SSID or passphrase, you will be asked to set up the extended network settings. You can save the settings by clicking on Next
• After the wireless range extender reboots, your computer device will need to be connected to the new network.
• Finally, click OK to set up your Range extender.

How do I connect wirelessly with the Amped wireless range extender

If your wireless adapter supports WPS One-Touch setup, Wi-Fi Protected Settingup is available.

• Press and hold the WPS button located on the back panel your Amped wireless range extender for approximately 3 seconds.
• The power LED on the amped wireless router will start to blink.
• Push the WPS button on your wireless adapter. Or, use the software provided to enable WPS.
• WPS will then automatically configure and establish connection settings for your wireless adapter in order to connect to your Amped wireless extender.

How can I reset my Amped Wireless Extender

These methods can reset the Amped wireless range extender to factory default settings:

Use the Reset button

Using the web interface

The steps below will help you to reset your computer by physically accessing the reset button.

• The reset button is located on the back panel.
• Use a pin or a straightened paperclip to press the reset button. After about five to ten second, release the reset button.
• Wait for a few minutes until the LED light flashes. This is an indicator that your Amped wireless range extender was restored to factory default settings.

To reset the amped wireless range extender using the web interface, log in to the web-based interface for amped wireless router

• Go to www.setup.ampedwireless.com through a web browser.
• To access the admin page, enter your default login credentials.
• Select Management from the menu.
• Click on Management to save/reload settings. Next, click on Reset Settings to default tab to restore factory settings for the amped wireless range extender.

What if you are unable to open the web menu of the amped wireless range extender after you enter the www.setup.ampedwireless.com?

• Make sure your computer is connected with the WIFI network for your range extender
• You should ensure that you’re using the most recent and compatible browser. If you still have issues, try switching to a different browser (recommended Google Chrome), or closing and reopening the same browser.
• Try using the default IP address 192.168.1.240 to access login page instead of web address setup.ampedwireless.com.
• Power cycle the Amped wireless range extender.
• The rest will change your settings to factory defaults so make sure you reset the range extender. You can reset the amplified wireless range extender by holding down the reset button for a few seconds, then releasing the button.
• If none of these steps work, disconnect your computer from any Wi-Fi networks. Then connect your computer to range extender via an Ethernet cable. Then try to access the web menu of the amped wireless range extender through www.setup.ampedwireless.com.

What happens if the Amped wireless range extender isn’t able to access the internet?

• Your internet connection to your Home Network may have dropped, or settings might have been changed due to a power surge. Therefore, you will need to connect to the Range Extender and access the web interface using the web address http://setup.ampedwireless.com. To reconnect the Range Extender with your wireless network, run the smart setup Wizard
• Access the setup web menu through setup.ampedwireless.com to check that the signal strength between the Range Extender and your Home Network is above 70%. The problem occurs when the Range Extender’s signal strength drops below 70% because it is too far away from your router. The signal strength between your router and Range Extender can be checked by clicking on the link to the left of the web menu. The section Home Wireless Network Settings will display the Signal Strength reading. It must be at least 70%. If signal strength falls below 70%, then you need to move your amped wireless range extender closer to your router or reposition it.

How do you find the best location for your wireless range extender amped?

The Signal Strength LED is located at the front of the amp wireless range extender. It can be used to find the perfect or optimum setting.

• Green LED: An Excellent Signal Above 70%
• Yellow LED: Moderate signal strength between 60-69%
• Red LED: Signal strength below 59%
• After turning on the amplified wireless extender, it takes approximately 1-3 minutes for the signal to register. The LED can be used as a guide to help you position the Extender in a better place after the extender setup. Signal strength should not be less than 70%. LED is green.

Please Note: If the range extender setup has not been completed, the signal strength LED won’t turn on.

setup.ampedwireless.com – How to setup and install Amped Wireless AC1900 Wi-Fi Router (B1900RT)?

setup.ampedwireless How to update Amped wireless device firmware

The firmware controls how the device works, so it is imperative to update Amped wireless extender’s firmware regularly for better working, Wi-Fi stability, and performance. It is possible to update the amped wireless router or Amped wireless extender’s firmware either manually or automatically using setup.ampedwireless.com login to the amped wireless dashboard.

Download the latest firmware version file from the Amped Wireless official site. This is required for manual updating of the Amped wireless firmware. You will need to save the zip file you downloaded onto your computer. Then follow these steps:

• Connect the computer to the Amped wireless router using a recommended wired Ethernet cable at one of its four LAN ports.
• Open a web browser to access the amped wireless dashboard.
• Enter setup.ampedwireless.com for amped wireless login in the browser.
• When prompted, enter the default amped wireless login details as Administrator in the username/password fields.
• Go to the amped wireless admin page and select Amped wireless settings. Next, choose Management option.
• Click on the Upgrade Firmware option to upload the unzipped firmware file you have previously downloaded.

Follow the steps below to get an automatic firmware update of the Amped wireless firmware.

• Open a web browser to access the amped wireless dashboard.
• Enter setup.ampedwireless.com for amped wireless login in the browser.
• When prompted, enter the default wireless login details as Administrator in the username-password fields.
• The admin page for the amped wireless device will be accessible.
• Click on Administration and then click the Amped router firmware.
• To enable automatic wireless configuration of the firmware version file, click on the “Check” button.

Note: Clicking on the check button via setup.ampedwireless.com login lets the amped wireless users to know when their device requires firmware update and checks for the availability of latest firmware versions to be downloaded automatically.

• The firmware file will be automatically searched for by the amped wireless device and uploaded. This entire process takes approximately 3-5 minutes.
• After the Amped wireless automatic firmware upgrade is completed, the router will automatically reboot.

To avoid serious damage or corruption of firmware, ensure that power cycling of the amplified wireless device takes place without interference or disturbance.

Why setup.ampedwireless.com pages are not working?

How to port forward the setup.ampedwireless.com in an Amped router?

Port Forwarding allows you to forward a request from a port into a mobile device on a private network. This feature is used to set up cameras, mobile devices, or servers that require remote access. Port forwarding requires that you know the IP address for the mobile device to which you wish to Port Forward requests. To enable as well as to configure the Port Forwarding, a user has to visit the web interface of the setup.amepdwireless.com window.

Steps to port forward the setup.ampedwireless.com in an Amped router

1. Use the browser to access the Amped router from a computer or laptop.
2. Take your cursor to the address bar and type www.setup.ampedwireless.com as the URL of your browser. Click the Enter button. If you experience an error, you can type 192.168.1.1 on the address bar.
3. The default Amped router login page will appear on your screen when you press the enter key. If this is your first time connecting to your router, the QoS setup page will appear on your screen.
4. Mention your login credentials in the respective fields. As a default login credential, type “admin” in the username field. Enter the password that you have assigned to your Amped router during setup. If you haven’t changed your default password, enter “admin” instead. Both login fields are case sensitive.
5. After entering your credentials, click the Login button located under the login fields.
6. You will be redirected to the main screen of the setup.ampedwirleless.com window.
7. Enable the Port Forwarding feature by enabling the port from which you wish to Port Forward multiple requests.
8. Go to the IP Address field and enter the IP address for the device being used for Port Forwarding. You must know the IP address for the device you wish to Port Forward.
9. Select the Protocols you wish to forward through the Port Forwarding method. You can choose between UDP and TCP depending on your requirements. The drop-down menu located on the right side is the Protocol tab. You can choose the protocol you want to use. The protocols are requests being port forward to a private network so it is important to choose wisely.
10. Scroll down to Port Range and choose the port range for the assigned IP address to which you want to forward the specific requests.
11. Finally, move your cursor to “Comment” and enter a name you wish to give to users in order to identify the Port Forwarding entry. A user will not be able identify the Port Forwarding Entry entry if they don’t assign a name. A name can be assigned to the Port forwarding entry, which makes it easier for users to identify it.
12. After you have completed applying the Port Forwarding rules settings, click the Apply button. The settings will be applied.

Notice: Make sure the user is familiar with the protocol he wishes to use on the network settings being port forward to the device in the local network. Port Forwarding is used primarily for hosting mail servers and web servers behind firewalls.

If an Internet connection is abnormally slow after the setup.ampedwireless.com setup process

Sometimes, the internet becomes inaccessible after setup. During this time, the Internet switches between a temporary and a permanent connection. It is essential that the router be properly configured during setup. If a user experiences sudden loss of bandwidth or abnormal behavior when using the Internet, there are troubleshooting options that can be used to fix the problem.

1. Ask your Internet Service Provider if they are experiencing a Wide Area Network problem. You cannot help them if they have a WAN problem. However, the issue will be fixed after some time.
2. To test the speed of your Internet Service Provider’s Internet connection, you can use a speed test function. You can also use speed testing applications to determine the speed of your Internet connection. You can also visit the interface of setup.ampedwireless.com window to identity the speed of your internet in the network. If you get the same speed results, this means the problem is with your Internet Service Provider. To resolve your Internet problem, you can contact your ISP.
3. Switch to another device and disconnect your router from the computer that you are using for internet access. Your computer may have an operating system issue or hardware problem if the issue does not occur on the second computer or mobile device. You should ensure that your computer is up-to-date and has the firewall and antivirus softwares installed. Sometimes bugs and viruses can slow down your computer’s speed, which directly affects your internet speed.
4. If your Amped router has a wireless connection, the front panel can be used to check the signal strength. Signal bars above 3 indicate that your router is at the right distance from your computer. You should bring your router closer to your computer if the signal bars are lower than 3. A user can also check the Network Status of his router through the menu dashboard of the setup.ampedwireless.com window.
5. You must ensure that your browser is up-to-date and has no cache. Sometimes, the cache files can accumulate in the cache memory and cause problems for users or make it difficult to use the internet. The settings tab in a browser can be used to erase the cache.